Working on this vehicle? Write estimates, send inspections & invoice customers from your phone.

    Start 14-Day Free Trial
    ← All vehicle specs
    Serpentine Belt Routing & Length

    2019 Honda Accord Serpentine Belt Routing & Replacement

    Everything on this vehicle

    Working on this 2019 Honda Accord? Run just this one job through Repairius.

    No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.

    14-day free trial · credit card required · cancel anytime

    Quick Answer

    • Belt Length: Approximately 79.5 inches (2020 mm)
    • Rib Count: 6-rib
    • OEM Belt Part Number: 31110-6A0-A01 (for 1.5L and 2.0L engines)
    • Aftermarket Cross-references:
      • Gates K060795
      • Dayco 5060795
      • Continental Elite 4060795
    • Auto-Tensioner Part Number: 31170-6A0-A01 (for 1.5L and 2.0L engines)
    • Idler Pulley Part Number: 31190-5A2-A02 (for 1.5L and 2.0L engines)

    Belt Routing

    The 2019 Honda Accord serpentine belt routing can be tricky, so it's always a good idea to take a clear photo of the existing belt routing before you begin removal. This will serve as an invaluable reference during reinstallation.

    Here's a typical routing path for the 1.5L and 2.0L engines:

    1. Starting from the crankshaft pulley (the large pulley at the bottom, closest to the front of the vehicle), the belt travels upwards.
    2. It then goes to the A/C compressor pulley (located lower on the passenger side).
    3. From the A/C compressor, the belt routes over the top of the idler pulley (a smooth pulley that guides the belt).
    4. The belt then travels upwards to the alternator pulley (typically located higher on the passenger side).
    5. From the alternator, it makes its way across to the power steering pump pulley (if applicable; some models have electric power steering and no pump).
    6. Next, the belt wraps around the water pump pulley (usually on the driver's side, mid-height).
    7. Finally, the belt goes under the automatic tensioner pulley (a spring-loaded pulley that provides constant tension to the belt), completing the circuit back to the crankshaft pulley.

    Note: While this description covers the common routing, slight variations can exist between the 1.5L and 2.0L engines, especially regarding accessories like the power steering pump. Always double-check your specific engine configuration against your pre-removal photograph.

    How to Replace the Serpentine Belt

    Replacing the serpentine belt on your 2019 Honda Accord is a manageable DIY task, but it requires patience and the right tools. Here's a general overview:

    1. Safety First: Ensure the engine is cool and the vehicle is securely supported on jack stands if you need to access it from underneath. Disconnect the negative battery terminal.
    2. Locate the Tensioner: Identify the automatic belt tensioner. It will have a square opening, typically 3/8-inch, designed for a breaker bar or a specialized serpentine belt tool.
    3. Relieve Tension: Insert a 3/8-inch breaker bar or serpentine belt tool into the square opening of the tensioner. Rotate the tensioner counter-clockwise (or sometimes clockwise, depending on the engine) to relieve the tension on the belt. This will allow the belt to become loose.
    4. Remove the Old Belt: While holding the tensioner in the loosened position, carefully slip the old serpentine belt off one of the pulleys.
    5. Inspect Pulleys: With the belt removed, inspect all pulleys for wear, damage, or excessive play. Spin each pulley by hand; they should turn smoothly with no grinding noises. Also, check the tensioner for proper operation and any signs of weakness.
    6. Route the New Belt: Referring to your pre-removal photo or the routing description above, carefully route the new serpentine belt over all the pulleys, leaving the tensioner pulley for last or one of the easily accessible pulleys for the final placement.
    7. Final Tensioning: Once the belt is mostly in place, use your breaker bar or serpentine belt tool to once again relieve the tensioner. Slip the belt onto the last pulley. Slowly release the tensioner, ensuring the belt is properly seated in all the pulley grooves.
    8. Double-Check: Start the engine and let it run for a minute or two. Observe the belt's operation to ensure it's tracking correctly and there are no abnormal noises. Turn the engine off and re-check the belt's seating on all pulleys.

    Replacement Interval

    Honda typically recommends inspecting the serpentine belt at regular service intervals, usually every 15,000 to 30,000 miles, and replacing it as needed. Often, the belt can last much longer, potentially between 60,000 to 100,000 miles, depending on driving conditions and maintenance. However, it's crucial to replace it if you notice any signs of wear.

    Signs of a Failing Belt or Tensioner

    Ignoring a failing serpentine belt or tensioner can lead to a breakdown, as the belt drives critical components. Here are key signs to watch for:

    • Squealing or Chirping Noises: This is one of the most common indicators. A loose, worn, or misaligned belt, or a failing tensioner or pulley, can cause these noises, especially on cold starts or when turning the steering wheel.
    • Cracks, Fraying, or Glazing on the Belt: Visually inspect the belt. Cracks on the ribbed side, fraying along the edges, or a smooth, shiny (glazed) appearance indicate wear and a need for replacement.
    • Loss of Power Steering, A/C, or Charging System Issues: If the belt breaks or slips significantly, the components it drives will stop working. This can manifest as heavy steering (loss of power steering), no cold air from the A/C, or the battery warning light illuminating on your dashboard (alternator not charging).
    • Vibrations: Excessive vibrations coming from the engine accessories can be a sign of a failing tensioner or a worn pulley bearing.
    • Belt Slipping Off Pulleys: If the belt frequently slips off a pulley, it indicates either a severely worn belt, a faulty tensioner, or a misaligned pulley.
    • Wobbling or Sticking Tensioner: With the engine off, visually inspect the tensioner. It should appear steady. If it wobbles excessively or if the pulley appears to be sticking when you try to move it, the tensioner may be failing.

    Don't wait for a complete belt failure. Address these symptoms promptly to avoid being stranded.

    Find a trusted shop on Repairius.

    Need service on your Honda Accord?

    Your vehicle and question are already filled in — just add your location.

    More specs for the 2019 Honda Accord

    Oil Capacity & Filter

    Capacity, weight, filter PN, drain plug torque, change interval.

    Fluid Type Specs

    Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.

    Coolant Capacity & Type

    Total system capacity, OEM coolant spec, flush interval, bleed tips.

    Transmission Fluid & Service

    Trans model, fluid spec, capacity, filter PN, service interval.

    Torque Specifications

    Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.

    Brake Pad & Rotor Specs

    Pad PNs, rotor size, min thickness, caliper torque.

    Tire Size & Pressure

    OEM size, cold psi, bolt pattern, wheel size, TPMS.

    Battery Size & Group

    Group size, CCA, AGM/flooded, dimensions, reset note.

    A/C Refrigerant & Oil

    R-134a or R-1234yf, charge oz, PAG oil spec.

    Bulb Sizes (Headlight, Tail, Fog)

    Headlight, fog, tail, turn, reverse, interior.

    Factory Maintenance Schedule

    Service intervals by mileage, severe-duty notes, known issues.

    Towing Capacity & Payload

    Max tow, payload, GVWR/GCWR, hitch class by trim.

    Fuse Box Diagram & Amperage

    Fuse box locations, layout, amps, and what each fuse controls.

    Wheel Alignment Specifications

    Camber, caster, toe ranges (front & rear), adjustability notes.

    Paint Color Codes

    All factory colors with paint codes, sticker location, touch-up tips.

    Wiper Blade Sizes

    Driver/passenger/rear blade size, attachment, OEM + cross-refs.

    Spark Plug Type & Gap

    Plug PN, gap, torque, interval by engine.

    Transmission & Axle Gear Ratios

    Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.

    Key Fob Programming

    DIY programming steps, FCC ID, fob PN, battery, transponder.

    Same spec — other model years

    Maintenance & repair guides

    Browse by make

    Running an auto or diesel repair shop?

    Compare Repairius to the shop software you're paying for

    $99.99/month (first location included), unlimited users, 14-day free trial.

    Values can vary by engine, trim and build date; check your VIN-specific service information. Updated 2026-06-22.

    Run your shop from estimate to payment

    Don't overhaul your shop. Test Repairius on your next job.

    Repairius keeps estimates, work orders, real-time job assignment, customer and vehicle history, inventory, and payments in one place — on desktop and in your pocket.

    14-day free trial · credit card required · cancel anytime

    Not a mechanic? Send Repairius to your shop — they can run estimates, jobs, and invoices in one place.

    Know someone who needs this?

    Share this page with a mechanic, a shop owner, or a friend working on the same problem.

    Know a mechanic or shop owner Repairius could help?

    Send them Repairius in one tap. Free listing, online booking, reminders and the full shop workflow.

    Text them Email