2019 Honda Accord Spark Plug Replacement Guide
Working on this 2019 Honda Accord? Run just this one job through Repairius.
No big switch. Write the estimate, text it for approval, and get paid on your phone. Keep everything else the way it is.
14-day free trial · credit card required · cancel anytime
Quick Reference: 2019 Honda Accord Spark Plugs
| Engine | OEM Plug P/N | Aftermarket Options (NGK/Denso) | Gap (in/mm) | Torque (lb-ft / Nm) | Interval (miles) |
|---|---|---|---|---|---|
| 1.5L Turbo (L15BE) | 12290-6A0-A01 | NGK DILKAR8P8SY, Denso DXE24HCR11S | 0.030 / 0.7-0.8 | 16 / 22 | 100,000 |
| 2.0L Turbo (K20C4) | 12290-59B-003 | NGK ILZKAR8H8S, Denso DXE27HCR-S11S | 0.030 / 0.7-0.8 | 16 / 22 | 100,000 |
Why the Right Spark Plug Matters
Selecting the correct spark plug is critical for engine performance, fuel efficiency, and longevity. It's not just about finding a plug that screws in; it's about matching the plug's characteristics to the engine's demands.
-
Heat Range: This is arguably the most crucial factor. A spark plug's heat range refers to its ability to dissipate heat from the combustion chamber. A "hotter" plug has a longer insulator nose, retaining more heat, while a "colder" plug has a shorter insulator nose and transfers heat more quickly to the cylinder head. The turbocharged, direct-injected engines in the 2019 Accord run at high temperatures and pressures, requiring a colder plug to prevent pre-ignition (or "knock"), which can cause severe engine damage. Using a plug that is too hot can lead to melted electrodes, while a plug that is too cold can lead to carbon fouling and misfires.
-
Electrode Material: The 2019 Accord, like most modern vehicles, comes from the factory with Iridium-tipped spark plugs.
- Iridium: This precious metal has an extremely high melting point and is incredibly hard, allowing manufacturers to create a very fine-wire center electrode. A fine wire concentrates the spark energy, requiring less voltage to jump the gap. This creates a more consistent, powerful spark, improving fuel efficiency, throttle response, and cold starting. Iridium plugs have the longest service life, often lasting up to 100,000 miles, as specified for both Accord engines.
- Platinum: A step down from Iridium, platinum plugs still offer excellent longevity and performance compared to older technologies.
- Copper: Standard copper plugs are excellent conductors and offer great performance, but they wear out much faster, sometimes needing replacement every 20,000-30,000 miles. They are not recommended for the 2019 Accord, as the ignition system is calibrated for the low voltage requirements and long life of iridium plugs.
How to Gap a Spark Plug
Most high-quality Iridium plugs, like the NGK and Denso plugs specified for the Accord, come pre-gapped from the factory. However, it's always wise to verify the gap before installation, as they can be mishandled during shipping.
- Use the Right Tool: Use a wire-style or feeler gauge gap tool, not the cheap "coin" style ones. The coin-style tools can put pressure on the fine-wire iridium electrode and damage it.
- Check the Gap: For both the 1.5L and 2.0L engines, the target is 0.030 inches. Gently slide the correct wire or feeler blade between the center electrode and the ground electrode. It should slide through with very light drag.
- Adjust if Necessary: If the gap is too wide, gently tap the end of the ground electrode on a hard surface to close it slightly. If it's too narrow, use the small hook on your gapping tool to gently pry the ground strap outwards. Never pry against or put pressure on the center electrode.
Replacement Procedure Tips for 2019 Accord
Both the 1.5L and 2.0L engines use a modern coil-on-plug ignition system, which simplifies the replacement process compared to older distributor-based systems.
- Engine Cover Removal: The engine is covered by a plastic beauty cover. This usually pulls off with a firm tug or may have a few small bolts or clips holding it in place.
- Coil-on-Plug Removal: Once the cover is off, you will see the individual ignition coils sitting on top of the valve cover, directly over each spark plug. Disconnect the electrical connector from a coil, then remove the single bolt (usually 10mm) holding it down. The coil can then be pulled straight up and out. A slight twisting motion can help break the seal if it feels stuck.
- The Anti-Seize Debate: This is a hotly debated topic. NGK, the OEM supplier, explicitly recommends not using anti-seize compound on their plugs that have a special trivalent (nickel or zinc-chromate) plating. This plating provides its own anti-corrosive properties and acts as a release agent. Applying anti-seize can alter the torque reading, leading you to over-tighten the plug, which can stretch the plug's metal shell and potentially cause it to fail or damage the cylinder head threads. For the OEM NGK or Denso plugs, install them dry into a clean thread.
- Dielectric Grease: While anti-seize on the threads is not recommended, applying a small amount of dielectric grease to the inside of the ignition coil boot is a good practice. This prevents the boot from sticking to the spark plug porcelain over time and helps seal out moisture, preventing corrosion on the terminal.
- Torque Correctly: Use a torque wrench. Over-tightening can damage the plug and cylinder head, while under-tightening can allow the plug to loosen from vibration, leading to poor heat transfer and potential damage. The correct torque for both engines is 16 lb-ft (22 Nm).
Known Issues
Fortunately, the 2019 Honda Accord's L15BE and K20C4 engines are not known for widespread, systemic spark plug issues like those seen in some other manufacturers. The problems you mentioned—such as the notorious two-piece spark plug breakage on Ford 3-valve Triton engines or cracked porcelain—are not common concerns on this platform. The design is robust and straightforward. As long as you use the correct OEM-spec Iridium plugs and proper installation technique, you can expect a long and trouble-free service life.
Need plugs replaced? Find a shop on Repairius.
Need service on your Honda Accord?
Your vehicle and question are already filled in — just add your location.
More specs for the 2019 Honda Accord
Oil Capacity & Filter
Capacity, weight, filter PN, drain plug torque, change interval.
Fluid Type Specs
Engine oil, coolant, ATF, diff, brake, PS, DEF — with OEM spec numbers.
Coolant Capacity & Type
Total system capacity, OEM coolant spec, flush interval, bleed tips.
Transmission Fluid & Service
Trans model, fluid spec, capacity, filter PN, service interval.
Torque Specifications
Lug nuts, drain plug, caliper, axle nut, plug, key fasteners.
Brake Pad & Rotor Specs
Pad PNs, rotor size, min thickness, caliper torque.
Tire Size & Pressure
OEM size, cold psi, bolt pattern, wheel size, TPMS.
Battery Size & Group
Group size, CCA, AGM/flooded, dimensions, reset note.
A/C Refrigerant & Oil
R-134a or R-1234yf, charge oz, PAG oil spec.
Bulb Sizes (Headlight, Tail, Fog)
Headlight, fog, tail, turn, reverse, interior.
Factory Maintenance Schedule
Service intervals by mileage, severe-duty notes, known issues.
Towing Capacity & Payload
Max tow, payload, GVWR/GCWR, hitch class by trim.
Fuse Box Diagram & Amperage
Fuse box locations, layout, amps, and what each fuse controls.
Serpentine Belt Routing & Length
Belt routing, length, rib count, OEM + aftermarket PNs.
Wheel Alignment Specifications
Camber, caster, toe ranges (front & rear), adjustability notes.
Paint Color Codes
All factory colors with paint codes, sticker location, touch-up tips.
Wiper Blade Sizes
Driver/passenger/rear blade size, attachment, OEM + cross-refs.
Transmission & Axle Gear Ratios
Trans gear ratios, axle ratios, RPO codes, tow vs MPG impact.
Key Fob Programming
DIY programming steps, FCC ID, fob PN, battery, transponder.
Same spec — other model years
Maintenance & repair guides
2019 Honda Accord Maintenance Schedule →
Available maintenance guidance; confirm the manufacturer schedule.
Repair planning references →
Plan the scope of work; detailed procedures need configuration-matched evidence.
Browse by make
Running an auto or diesel repair shop?
Compare Repairius to the shop software you're paying for
$99.99/month (first location included), unlimited users, 14-day free trial.
Values can vary by engine, trim and build date; check your VIN-specific service information. Updated 2026-08-19.